|
The old setup - stock steel bumper, Smitty Bumper Thumber
The old setup - stock steel bumper, Smitty Bumper Thumber
Date: 12/31/1969
Views: 3865
|
Bumper removed
Bumper removed
Date: 12/31/1969
Views: 1517
|
Two holes cut in the frame cap, 1.5x1.5 tube inside, 3x2x.250 angle sitting across the top and slightly notched.
Two holes cut in the frame cap, 1.5x1.5 tube inside, 3x2x.250 angle sitting across the top and slightly notched.
Date: 12/31/1969
Views: 4148
|
Two holes cut in the frame cap, 1.5x1.5 tube inside, 3x2x.250 angle sitting across the top and slightly notched.
Two holes cut in the frame cap, 1.5x1.5 tube inside, 3x2x.250 angle sitting across the top and slightly notched.
Date: 12/31/1969
Views: 2485
|
2x6x.188 tube for the main portion. Winch holes are drilled out and will be sleeved.
2x6x.188 tube for the main portion. Winch holes are drilled out and will be sleeved.
Date: 12/31/1969
Views: 3268
|
|
DCP_0006.JPG
DCP_0006.JPG
Date: 12/31/1969
Views: 1507
|
DCP_0007.JPG
DCP_0007.JPG
Date: 12/31/1969
Views: 1475
|
Lower 2x2x.250 notched on ends and then shaved the entire length to make the top and bottom snug with the frame, held in place.
Lower 2x2x.250 notched on ends and then shaved the entire length to make the top and bottom snug with the frame, held in place.
Date: 12/31/1969
Views: 4309
|
The 1.5 goes into the frame to where the bolt is. A piece of 2x.250 strap goes across the top of the frame to the same bolt hol
The 1.5 goes into the frame to where the bolt is. A piece of 2x.250 strap goes across the top of the frame to the same bolt hole. A 3/4" OD sleeve drops down from the top and into the 1.5 at the bottom so the bolt can be tightened without crushing
Date: 12/31/1969
Views: 1453
|
View from the front
View from the front
Date: 12/31/1969
Views: 1096
|
|
tracked together
tracked together
Date: 12/31/1969
Views: 1050
|
2x6 winch plate/bumper set in place
2x6 winch plate/bumper set in place
Date: 12/31/1969
Views: 1669
|
DCP_0013.JPG
DCP_0013.JPG
Date: 12/31/1969
Views: 1490
|
DCP_0014.JPG
DCP_0014.JPG
Date: 12/31/1969
Views: 2969
|
Winch channel set in place for demo purposes - I won't be using the mounting channel, and will fab up a fairlead mount.
Winch channel set in place for demo purposes - I won't be using the mounting channel, and will fab up a fairlead mount.
Date: 12/31/1969
Views: 1945
|
|
DCP_0016.JPG
DCP_0016.JPG
Date: 12/31/1969
Views: 5951
|
DCP_0017.JPG
DCP_0017.JPG
Date: 12/31/1969
Views: 1620
|
DCP_0018.JPG
DCP_0018.JPG
Date: 12/31/1969
Views: 1187
|
DCP_0019.JPG
DCP_0019.JPG
Date: 12/31/1969
Views: 1035
|
Winch set in place
Winch set in place
Date: 12/31/1969
Views: 2507
|
|
clearance with winch
clearance with winch
Date: 12/31/1969
Views: 1217
|
DCP_0022.JPG
DCP_0022.JPG
Date: 12/31/1969
Views: 1027
|
DCP_0023.JPG
DCP_0023.JPG
Date: 12/31/1969
Views: 1133
|
DCP_0024.JPG
DCP_0024.JPG
Date: 12/31/1969
Views: 952
|
Jacked bumper up another 3/4" for more ground clearance
Jacked bumper up another 3/4" for more ground clearance
Date: 12/31/1969
Views: 2609
|
