|
Checking droop
Checking droop
Date: 12/31/1969
Views: 1246
|
Roughly where I thought the shocks would come up
Roughly where I thought the shocks would come up
Date: 12/31/1969
Views: 799
|
Shorter slot on the passenger side after I decided the shocks could be run straight up, not angled.
Shorter slot on the passenger side after I decided the shocks could be run straight up, not angled.
Date: 12/31/1969
Views: 921
|
dcp 0014
dcp 0014
Date: 12/31/1969
Views: 748
|
Holding the new U-bolt plate based lower mount in place for testing
Holding the new U-bolt plate based lower mount in place for testing
Date: 12/31/1969
Views: 943
|
|
See the lower mount?
See the lower mount?
Date: 12/31/1969
Views: 772
|
To build the uprights for the hoop, I hole-sawed a single piece of tube, then cut it in half on the bandsaw
To build the uprights for the hoop, I hole-sawed a single piece of tube, then cut it in half on the bandsaw
Date: 12/31/1969
Views: 1329
|
To build the uprights for the hoop, I hole-sawed a single piece of tube, then cut it in half on the bandsaw
To build the uprights for the hoop, I hole-sawed a single piece of tube, then cut it in half on the bandsaw
Date: 12/31/1969
Views: 956
|
First mock up of the uprights
First mock up of the uprights
Date: 12/31/1969
Views: 799
|
Checking "bump" clearance
Checking "bump" clearance
Date: 12/31/1969
Views: 885
|
|
For the upper mounts, I hole-sawed some flat stock, which I then cut in half lengthwise to make a total of 4 tabs
For the upper mounts, I hole-sawed some flat stock, which I then cut in half lengthwise to make a total of 4 tabs
Date: 12/31/1969
Views: 999
|
The uprights
The uprights
Date: 12/31/1969
Views: 920
|
dcp 0023
dcp 0023
Date: 12/31/1969
Views: 3897
|
dcp 0024
dcp 0024
Date: 12/31/1969
Views: 1276
|
dcp 0025
dcp 0025
Date: 12/31/1969
Views: 815
|
|
Welding
Welding
Date: 12/31/1969
Views: 1294
|
dcp 0027
dcp 0027
Date: 12/31/1969
Views: 733
|
dcp 0028
dcp 0028
Date: 12/31/1969
Views: 905
|
Comparing a 7100 Remote Reservoir to a 5125 for ideas on how to affix the upper tabs
Comparing a 7100 Remote Reservoir to a 5125 for ideas on how to affix the upper tabs
Date: 12/31/1969
Views: 1090
|
After welding the mounts onto the bolt-in upright hoop.
After welding the mounts onto the bolt-in upright hoop.
Date: 12/31/1969
Views: 1063
|
|
dcp 0002
dcp 0002
Date: 12/31/1969
Views: 1530
|
dcp 0003
dcp 0003
Date: 12/31/1969
Views: 869
|
U-bolt plates after welding the lower mounts to them. They are offset to the outside of the vehicle.
U-bolt plates after welding the lower mounts to them. They are offset to the outside of the vehicle.
Date: 12/31/1969
Views: 2655
|
Paint
Paint
Date: 12/31/1969
Views: 967
|
Preparing to tear down one of the 7100s for revalving and a seal replacement on the reservoir
Preparing to tear down one of the 7100s for revalving and a seal replacement on the reservoir
Date: 12/31/1969
Views: 959
|
