|
Checking droop
Checking droop
Date: 12/31/1969
Views: 1266
|
Roughly where I thought the shocks would come up
Roughly where I thought the shocks would come up
Date: 12/31/1969
Views: 821
|
Shorter slot on the passenger side after I decided the shocks could be run straight up, not angled.
Shorter slot on the passenger side after I decided the shocks could be run straight up, not angled.
Date: 12/31/1969
Views: 944
|
dcp 0014
dcp 0014
Date: 12/31/1969
Views: 769
|
Holding the new U-bolt plate based lower mount in place for testing
Holding the new U-bolt plate based lower mount in place for testing
Date: 12/31/1969
Views: 964
|
|
See the lower mount?
See the lower mount?
Date: 12/31/1969
Views: 795
|
To build the uprights for the hoop, I hole-sawed a single piece of tube, then cut it in half on the bandsaw
To build the uprights for the hoop, I hole-sawed a single piece of tube, then cut it in half on the bandsaw
Date: 12/31/1969
Views: 1352
|
To build the uprights for the hoop, I hole-sawed a single piece of tube, then cut it in half on the bandsaw
To build the uprights for the hoop, I hole-sawed a single piece of tube, then cut it in half on the bandsaw
Date: 12/31/1969
Views: 978
|
First mock up of the uprights
First mock up of the uprights
Date: 12/31/1969
Views: 821
|
Checking "bump" clearance
Checking "bump" clearance
Date: 12/31/1969
Views: 908
|
|
For the upper mounts, I hole-sawed some flat stock, which I then cut in half lengthwise to make a total of 4 tabs
For the upper mounts, I hole-sawed some flat stock, which I then cut in half lengthwise to make a total of 4 tabs
Date: 12/31/1969
Views: 1022
|
The uprights
The uprights
Date: 12/31/1969
Views: 941
|
dcp 0023
dcp 0023
Date: 12/31/1969
Views: 3924
|
dcp 0024
dcp 0024
Date: 12/31/1969
Views: 1299
|
dcp 0025
dcp 0025
Date: 12/31/1969
Views: 837
|
|
Welding
Welding
Date: 12/31/1969
Views: 1318
|
dcp 0027
dcp 0027
Date: 12/31/1969
Views: 753
|
dcp 0028
dcp 0028
Date: 12/31/1969
Views: 928
|
Comparing a 7100 Remote Reservoir to a 5125 for ideas on how to affix the upper tabs
Comparing a 7100 Remote Reservoir to a 5125 for ideas on how to affix the upper tabs
Date: 12/31/1969
Views: 1113
|
After welding the mounts onto the bolt-in upright hoop.
After welding the mounts onto the bolt-in upright hoop.
Date: 12/31/1969
Views: 1085
|
|
dcp 0002
dcp 0002
Date: 12/31/1969
Views: 1551
|
dcp 0003
dcp 0003
Date: 12/31/1969
Views: 893
|
U-bolt plates after welding the lower mounts to them. They are offset to the outside of the vehicle.
U-bolt plates after welding the lower mounts to them. They are offset to the outside of the vehicle.
Date: 12/31/1969
Views: 2681
|
Paint
Paint
Date: 12/31/1969
Views: 990
|
Preparing to tear down one of the 7100s for revalving and a seal replacement on the reservoir
Preparing to tear down one of the 7100s for revalving and a seal replacement on the reservoir
Date: 12/31/1969
Views: 980
|
